Owens Corning Ridge Vent Installation Nationwide

Owens Corning Ridge Vent Installation: The Long Beach Owner’s Guide

We stock and install Owens Corning-compatible ridge vents across Long Beach, with most full ridge vent replacements running between $450 and $900 installed on a typical single-story home. If you’re calling because you spotted shingle granules in your gutter or noticed the plastic vent strip has cracked or pulled loose from the ridge line, you’re dealing with a ventilation failure that gets worse every summer. Erik Lindgren has walked enough Long Beach roofs to know the salt-laced air off the Pacific doesn’t forgive a brittle plastic vent, and we’ll tell you exactly what your roof needs before anyone climbs a ladder.

Call (562) 512-7366

Which Owens Corning Models This Applies To

Owens Corning sells ridge vent under two main lines: the VentSure series (rigid 4-foot strips, available in 9-inch and 11.5-inch widths) and the Deck Defense series, which pairs the vent with a weather-blocking filter membrane. The compatibility gotcha most homeowners miss: the 11.5-inch profile is sized for roofs with a thicker cap shingle or architectural shingle buildup, and mixing widths across a single ridge creates uneven airflow. If your original install used the narrower 9-inch strip, replacing it with an 11.5-inch vent means recutting the slot opening, not just swapping the plastic.

On identifying what you have: pull a section of the vent cap at the ridge end and look for the embossed Owens Corning part number on the underside. If it’s faded beyond reading, measure the exposed vent width. For OEM versus aftermarket: we install genuine Owens Corning vent material when we’re matching an existing run, and we’ll quote quality aftermarket equivalents from GAF or CertainTeed if you’re replacing the entire ridge and want to compare. Birchbark Roofing Long Beach is an independent service provider and is not affiliated with Owens Corning, which matters because we’re free to tell you when a different vent does the job better for less money.

Signs Your Owens Corning Ridge Vent Installation Is Failing

• Cracked or curled vent plastic along the ridge. UV exposure breaks down the polymer over time. In Long Beach, where roofs bake under direct sun most of the year, this shows up faster than in coastal fog belts. Once the plastic curls, rain gets driven into the attic opening.
• Granule buildup at gutter corners directly below the ridge. Failing ridge vent lets water work under adjacent cap shingles, accelerating granular loss. If you’re cleaning granules out of the same two gutter corners every few months, the vent is usually the culprit.
• Musty attic smell or visible moisture staining on rafters near the ridge. This means the vent strip has lost its weather seal at the ends. The filter membrane degrades, and wind-driven rain follows the ridge line inward.
• You can see daylight through the vent slot from inside the attic. A properly functioning ridge vent has a filter layer and baffle that blocks direct light. Seeing the sky means the baffle is torn or missing, and you’re losing attic warmth in winter while letting rain in.
• The vent has lifted off the ridge line and flapped loose in wind. This is the failure most Long Beach homeowners call us about after a Santa Ana wind event. The nails holding the plastic strip have pulled free, and the vent becomes a sail. This needs addressing before the next rain, not next season.

Replacement Cost & What’s Included

For most single-story Long Beach homes, replacing an Owens Corning ridge vent runs $450 to $900 installed, depending on the linear footage of the ridge, whether the cap shingles need re-bedding, and whether we’re working on a one- or two-story roof. A two-story home with a steep pitch pushes toward the top of that range because of ladder setup and fall protection requirements. The price includes removal of the failed vent, inspection of the slot opening for rot or water damage, installation of the new vent strip with proper fasteners, and re-seating of cap shingles along the full run. You’ll see the total in writing before any work starts, and our 365-Day Done Right Promise covers the installation: if it isn’t right, we make it right. Most ridge vent replacements take one roof visit of two to four hours.

DIY or Call Us?

Climbing onto any roof carries real risk, and ridge work puts you at the highest point of the house. If you want to check the vent yourself, do it from a ladder at the gable end where you can see the vent strip without walking the ridge. Photograph what you find and call us. What you should not do is pull old vent strips off the ridge and attempt a re-install, especially on a roof with a pitch steeper than 6:12. The fastening pattern matters for wind uplift, the end caps have to be seated correctly, and old plastic shatters under foot. Falls and broken vent material underfoot are exactly what a professional install avoids. Call (562) 512-7366, and we’ll have someone out to assess it.

FAQs